Cables

Fittings for converting open loop housing holders on a frame to traditional cable stops. - Fits snugly inside open loop and receives 5mm housing with no end cap - Large flange for larger hydraulic loops - Flattened on one side to accommodate frame

Jagwire's Aluminum Housing Connectors allow joining two sections of the same-size cable housings together in case you only have shorter sections and you need to make a longer one. It comes in 4 and 4.5mm diameters. Match the diameter of the housing sections on your bike. - Comes in a pack of 10

Rotating S-hooks securely hold housing segments together and prevent undue noise and migration. - Two halves rotate 360 degrees - Compatible with 4mm or 5mm housings

Rotating S-hooks securely hold housing segments together and prevent undue noise and migration. - Two halves rotate 360 degrees - Connects 4mm or 5mm housing to electronic shift wire

Jagwire's Straddle Cable Carrier is for cantilever and centerpull brakes. It attaches to the end of the brake cable and is what the brake's straddle (also called transverse or crossover) cable attaches to. The Straddle Cable Carrier is made of light, corrosion-resistant and durable aluminum with a steel bolt. You get a pack of 10.

SRAM's Line/Housing Frame Protectors are rubber covers that simply press onto your cable housings and or hydraulic lines to prevent the housings from hitting the frame and rattling or damaging the finish. There are 4 protectors in each package.

- Wet or muddy condition cable sealing solution - 4/6mm

Pro Compressionless brake housing eliminates flex from cable actuated braking systems, increasing power and improving lever feel. Included in this kit: - 6 x 5mm EZ-Bend segments - Flexible segments slot between road shifter hoods and Pro Compressionless housing run to allow for an appropriate bend at the handlebars

Protection where it's needed; Tube Tops can be placed virtually anywhere cable housing comes into contact with a bicycle frame. Designed to protect a frames finish Tube Tops can also be used to quiet cable slap.

Origin-8's Pro Cable Guide Pulley fulfills all your special cable routing needs. Designed to clamp onto seat tube, it allows you to route your cable for bottom pull front derailleurs. Uses a sealed bearing pulley.

Jagwire's Cable Grips are adapters that make it possible to run hydraulic brake lines on bicycle frames that have housing stops that were designed for regular wire cables and standard housing sections. Once the regular cables and housing sections are removed, the Cable Grips are inserted and tightened in place in the standard frame stops. Then, the hydraulic lines are attached and securely held in place by the gripping jaw(s) of the Cable Grips. - Aluminum model accepts lines up to 5mm in diameter and the lines snap in. - Stainless model grips fully around the lines and is adjustable to fit most diameters.

Sport level brake cables come in a variety of cable end setups to fit most bikes at a quality level well above normal OEM cables. - Slick cables are die-extruded for smooth operation - Pre-stretched - Double-ended SRAM/Shimano mountain and road compatible cable ends - Stainless steel construction resists corrosion - Double Ended: Yes - Cable Head: Shimano/SRAM Road, Shimano/SRAM Mountain - Defined Color: Silver - Quantity Included: 1

Jagwire's M7 Adjusting Barrel is a 7 x 1.0mm-threaded replacement cable-adjusting barrel. It's the right part for many older-style mountain bike brake levers. It comes in two models and is made of durable metal with a lockring for locking your adjustments. You get a pack of 10.

Jagwire's Mickey Adjusting Barrels are quality adjusters that mount to most road frames. They make it easy to fine-tune your shift cable tension by hand for optimum shifting performance.

Slick stainless cables undergo a polishing process to further remove imperfections. This creates a smoother surface with lower friction than PTFE-coated cables. With no coating, these are highly durable and compatible with all performance housings and lubricants. Typically used on high-end bikes, by riders wanting improved performance. Pro Polished cables eliminate the need for flaky coatings with an innovative polishing process to reduce friction and improve performance. - Polished stainless steel construction for low friction - Compatible with all performance housing and lubricants - Cables are tinted gold for easy identification

Slick stainless cables undergo a polishing process to further remove imperfections. This creates a smoother surface with lower friction than PTFE-coated cables. With no coating, these are highly durable and compatible with all performance housings and lubricants. Typically used on high-end bikes, by riders wanting improved performance. Pro Polished cables eliminate the need for flaky coatings with an innovative polishing process to reduce friction and improve performance. - Polished stainless steel construction for low friction - Compatible with all performance housing and lubricants - Cables are tinted gold for easy identification

Hose fittings for Hayes hydraulic disc brakes available a la carte. Hayes brake compatibility: - HFX-9 - Prime - Sole - El Camino - Radar

- Break-Away Quick Disconnect - Time-saving system for managing brake cables on Break-Away bikes - Light threaded alloy barrels with rubber noise dampener - Available for both derailleur and brake cables - Brake Quick Disconnect sold individually

Aluminum, Lightweight, Lubricated An alternative to traditional compressionless housing, this system is made of nesting alloy pieces that protect the liner. Although this housing is typically more expensive, it has several advantages including increased flexibility, reduced weight and increased durability. Both shift and brake housings use identical Slick-Lube liners and interconnecting alloy pieces. - Slick-Lube liners reduce friction and protect against corrosion - Includes four 1600mm liners

Aluminum, Lightweight, Lubricated An alternative to traditional compressionless housing, this system is made of nesting alloy pieces that protect the liner. Although this housing is typically more expensive, it has several advantages including increased flexibility, reduced weight and increased durability. Both shift and brake housings use identical Slick-Lube liners and interconnecting alloy pieces. - Slick-Lube liners reduce friction and protect against corrosion - Includes four 2300mm liners

Jagwire's Stick-On Cable Guides are made of lightweight aluminum with adhesive on the bottom. The aluminum lets them conform to any shaped frame tube and the adhesive holds fast. They come with Jagwire's C-Clips, nylon cable clips that snap onto the guides to hold the cables neatly in place. You get a pack of 4.

Jagwire's M6 Adjusting Bolt is a metal adjusting barrel that is the correct replacement adjusting barrel for the cable clips/hangers found on many cable brake systems old and new. It makes it easy to tighten/loosen your brakes without tools. Its 6 x 1.0mm threading fits most clips/hangers and it has a lockring for locking your brake adjustment once it's set. You get a pack of 25.

Jagwire's Sport Inline Adjusters are installed on your shift cable housing sections so that you can fine-tune the shift cable tension by hand (without tools). They're great for keeping your shifting dialed in. They're precision made of lightweight aluminum and nylon for easy use and durability. To install them, remove the cables and housing sections, cut the top housing sections in two and rejoin the sections with the Inline Adjusters in the middle.

- Front or rear brake compatible - Road specific - 1.5mm polished stainless steel cable

- For either front or rear shifter - Road & MTB compatible - 1.1 polished stainless steel cable

Replacement parts for Jagwire's Elite Link kits keep things functioning as intended. - Extra links for long housing runs or replacing damaged sections - 20 links at 10mm of length each

Inline adjusters make on-the-fly derailleur cable tension adjustments safe and easy. - 5mm - Stronger detent mechanism for use with brake housing - Perfect for mechanical disc brakes

Inline adjusters make on-the-fly derailleur cable tension adjustments safe and easy. - Indexed adjustment for braided shift housing - Not recommended for use with brake systems - Size: 4.5mm

- Aluminum straddle cable carrier for cantilever brake

SRAM's Inline Barrel Adjusters are placed on your shift cables near the handlebars so that you can turn the adjusters to fine-tune your shifting. They feature durable and light aluminum/composite construction with rubber covers for easy operation.